 |
|
|
|
| |
PRODUCT INFORMATION ‑ SPECIFICATION ‑ HEALTH & SAFETY SHEET
|
Product: |
PRO 1 Heavy Duty Stripper |
|
PRO 1 is a powerful scientific blend of chemical agents with very low foaming properties, which attacks even the heaviest build‑up of dirt and emulsion floor dressings with ease.
The excellent penetrating power of PRO 1 will enable light coatings of emulsion dressing to be removed manually where it is difficult for a machine to operate.
Allow PRO 1 to soften the dressing for approximately 10 minutes. Then agitate with the mop or nylon pad. Then remove slurry by mop or wet‑suction vacuum.
When operating a single brush floor scrubbing machine or an automatic scrubber‑drier we recommend the following. Firstly allow a short time for the Solution of PRO 1 to soak and soften the floor dressing. Then scrub using a black stripping pad and finally vacuum up the slurry.
When using the automatic scrubbing machine, double scrub leaving the vacuum off on the first pass, then vacuum up the slurry on the second pass. There is no need to rinse the floor because of the chemical make up of the product.
But we recommend rinsing the floor surface to make sure all the slurry has been removed before applying the emulsion dressings
The unique formulation makes PRO 1 become a powerful universal cleaning.
PRO 1 is an excellent product for automatic scrubber‑driers due to the low foaming properties. |
|
Recommended Uses: |
Rubber,Vinyl, Vinyl Asbestos, Thermoplastic, Asphalt, Linoleum, Composition, Terrazzo, Marble, Concrete, Quarry Tiles, Ceramic Tiles, Brick, Wood and Cork floors |
|
DIRECTIONS FOR USE |
Recommended for use on: Rubber. Linoleum, Vinyl, Vinyl Asbestos, Thermoplastic, Asphalt, Composition, Terrazzo, Marble, Finished Concrete, Quarry Tiles, Ceramic Tiles and all sealed Wood and Cork floors.
Although Linoleum and Rubber should always be treated with care, Pro 1 is safer to use on these than most floor strippers. |
| |
1. Container Sizes & Types |
|
|
|
5 liter, 25 liter polyurethane containers. |
|
|
|
2. INGREDIENTS |
% BY Weight |
Classification |
Occupational Exposure Limits |
Propylene Glycol n‑Butyl Ether |
5‑15 |
Xi R36/38 |
|
Alcohol Alkoxylate |
1‑5 |
Xi R36 |
|
Xylene Sulphonate |
5‑15 |
Xi R36 |
|
Sodium Metasilicate |
5‑15 |
C R34 |
|
Dietanolamine |
1‑5 |
Xi R36/38 |
TWA 3ppm 15mg/m3 |
Isopropanol |
5‑15 |
F R 11 Xi R36 |
STEL 50Oppm
1225mg/m3
TWA 400ppm
980 mg/m3 |
Ethylene Diamine Tetra‑Acetic
Acid, Tetra Sodium Salt |
1‑5 |
Xi R36 |
|
Water |
To 100% |
|
|
3. HEALTH HAZARD |
|
|
Corrosive: |
Yes |
|
Contains: |
Isopropanol 6%Sodium Metasilicate. |
|
Danger: |
R34 ‑ Causes burns |
|
4. FIRST AID & TREATMENT |
|
|
|
In the event of contact with skin, wash with copious quantities of water.
In the event of contact with eyes, wash with copious quantities of water.
In the event of ingestion, drink plenty of water and obtain medical advice immediately. |
|
5. FIRE FIGHTING MEASURES |
|
|
|
NIA |
|
6. ACCIDENTAL RELEASE MEASURES |
|
|
|
Small spills can be handled with a mop and water, large spills should be contained with sand or sawdust and disposed of under local authority regulations. |
|
7. HANDLING & STORAGE |
|
|
|
Store at room temperature,
Protect from freezing.
KEEP OUT OF REACH OF CHILDREN
Shelf life 2 years. |
|
8. PERSONAL PROTECTION |
|
|
|
Avoid contact with the skin. May cause mild irritation to sensitive skin if frequent contact with unprotected skin. Wear protective gloves and clothing.
Avoid contact with the eyes and face with safety glasses and face shield.
This product should not be ingested. Will cause corrosive damage to mouth, throat, and gastrointestinal tract.
Keep away from food or sources that could be ingested.
KEEP OUT OF REACH OF CHILDREN |
|
9. PHYSICAL & CHEMICAL PROPERTIES |
|
|
Appearance, Colour/ Odour: |
Blue liquid with characteristic odour. |
|
Solubility in Water: |
Completely |
|
Biocidal Activity: |
NIA |
|
Solubility inOrganic Solvent: |
Not soluble |
|
pH: |
13.3 |
|
Flash Point: |
41 degrees C. Does not support combustion. |
|
Density: |
1.085 |
|
Stability: |
Stable |
|
Incompatibility: |
Strong Acids |
|
10. STABLE & REACTIVITY |
|
|
Stability: |
Stable |
|
Materials to Avoid: |
Strong Acids |
|
Hazardous Decomposition Products:: |
None |
|
11. TOXICOLOGICAL INFORMATION |
|
|
Acute Oral LD 50: |
2000mg/kg (Rat). |
|
Danger: |
Causes severe eye damage.
Causes burns to skin.
Will cause damage to mouth, throat and gastrointestinal tract. |
|
12. ECOLOGICAL INFORMATION |
|
|
|
All material used in this product are biodegradable except Sodium Metasilicate which is inorganic, it will rapidly depolymermise into molecular species indistinguishable from natural dissolved silica. However the pH of the concentrated product is above the acceptable limits for direct discharge to sewers of watercourses. |
|
13. DISPOSAL CONSIDERATIONS |
|
|
|
The pH of the concentrated product is above the acceptable limits for direct discharge to sewers or watercourses. Consult local regulations for disposal. |
|
14. TRANSPORT INFORMATION |
|
|
ADR/R1D/IMDG: |
Classified
UN No. 1760
Class 8.
Packing Group 111. |
Corrosive |
15. REGULATORY INFORMATION |
|
|
Classified: |
Corrosive |
|
Risk Phrase 34 |
Causes bums. |
|
Safety Phrases S2 |
Keep out of reach of children. |
|
S 26 |
In case of contact with the eyes, rinse immediately with plenty of water and seek medical advice. |
|
S 37 139 |
Wear suitable gloves and eye 1 face protection. |
|
Contains: |
|
|
|
Sodium Metasilicare. |
Isopropanol 6% |
|
Non‑ionic Surfactants: |
Less than 5% |
|
Anionic Surfactants: |
5% and above, but less than 15% |
|
EDTA: |
Less than 5% |
16. OTHER INFORMATION |
|
|
|
N/A |
|
|
|
|
|
| |
| |
Total Floor Care, Jamsey Barton, Merridge Hill, Spaxton,Bridgwater, Somerset.TA5 1BB | Telephone: 01278 671185 Email: info@totalfloorcare.com |
|
|
|